Mazda 3 since 2003
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
6.1. General information
6.2. Brake system
6.2.1. Check and adjustment of elements of the brake system
6.2.2. Check of level of brake fluid in a tank of a hydraulic actuator of the working brake system
6.2.3. Removal of air from the brake system
6.2.4. Check of the backpressure valve of a vacuum hose (amplifier of brakes)
6.2.5. Removal and installation of a vacuum hose (amplifier of brakes)
6.2.6. Removal and installation of a pedal of a brake
6.2.7. Removal and installation of the main brake cylinder
6.2.8. Check of the sensor of level of liquid
6.2.9. Removal and installation of the vacuum amplifier of brakes
6.2.10. Check of the vacuum amplifier of brakes
6.2.11. Dismantling and assembly of the main cylinder
6.2.12. Removal and installation of a forward brake disk
6.2.13. Replacement of front brake shoes
6.2.14. Removal and installation of the back disk brake mechanism
6.2.15. Check of the parking brake system
6.2.16. Removal, check and installation of the back sensor of speed of a wheel of ABS
6.2.17. Removal and installation of the hydraulic block of anti-blocking system of brakes
6.2.17.1. Installation
6.3. Tables
7. Onboard electric equipment
8. Body
 








6-2-17-snyatie-i-ustanovka-gidravlicheskogo-bloka-antiblokirovochnojj-sistemy-tormozov.html

6.2.17. Removal and installation of the hydraulic block of anti-blocking system of brakes





ATTENTION
Internal elements of the hydraulic block of anti-blocking system of brakes can be damaged when falling the block on a firm surface. You watch to dropping the hydraulic block of anti-blocking system of brakes. Replace the hydraulic block of anti-blocking system of brakes if it underwent blow.

Гидроблок антиблокировочной системы тормозов
Fig. 6.61. Hydroblock of anti-blocking system of brakes: 1 – socket; 2 – brake highway; 3 – knot of the hydraulic block of anti-blocking system of brakes, arm; 4 – arm; 5 – control unit of anti-blocking system of brakes; 6 – hydraulic block of anti-blocking system of brakes



Remove the rechargeable battery and the platform of the rechargeable battery.
Remove a hose (models with the mechanical transmission).

Отсоединение разъема
Fig. 6.62. Socket detachment


Lift a socket cover in the direction of an arrow, pressing at the same time a uvula of a cover (fig. 6.62).
Pull the socket to a forward part of the car and remove it.

Нанесение установочных меток на тормозной магистрали и гидравлическом блоке антиблокировочной системы тормозов
Fig. 6.63. Drawing adjusting tags on the brake highway and the hydraulic block of anti-blocking system of brakes


Put an adjusting tag on the brake highway and the hydraulic block of anti-blocking system of brakes (fig. 6.63).
Wind the socket with a protective tape to prevent hit of brake fluid inside.
Remove the brake highway.

Снятие узла гидравлического блока антиблокировочной системы тормозов
Fig. 6.64. Removal of knot of the hydraulic block of anti-blocking system of brakes


As shown in the figure 6.64, move an arm in the direction of an arrow and remove knot of the hydraulic block of anti-blocking system of brakes and an arm from a body.

"previous page
6.2.16.4. Check of a form of a signal
following page"
6.2.17.1. Installation