Mazda 3 since 2003
1. Operation and maintenance of the car
1.1. Description of the car
1.2. System of passive safety
1.3. Use of the car to destination
1.4. Elimination of the malfunctions which arose in way or before a start of motion
1.4.1. Spare wheel and set of tools
1.4.2. Engine overheat
1.4.3. Evacuation of the car
1.4.4. General information and security measures at control survey and maintenance of the car
1.4.4.1. Check of level of engine oil
1.4.4.2. Check of level of cooling liquid
1.4.4.3. Check of level of working liquid in a tank of the steering hydraulic booster
1.4.4.4. Check of level of working liquid of automatic transmission
1.4.4.5. Check and adjustment of the parking brake
1.4.4.6. Check of an axial side play of a steering wheel
1.4.4.7. Replacement of an oil filter
1.4.4.8. Replacement of engine oil
1.4.4.9. Check of level and replacement of oil in MKPP
1.4.4.10. Check of level of liquid of washers of glasses and headlights
1.4.4.11. Lubricant of frictional units on a car body
1.4.4.12. Replacement of the filtering air cleaner filter element
1.4.4.13. Replacement of brushes of screenwash
1.4.4.14. Service of the rechargeable battery
1.4.4.15. Check of level of electrolyte
1.4.4.16. Charge of the rechargeable battery
1.4.4.17. Check of pressure of air in tires
1.4.4.18. Periodic shift of wheels
1.4.5. Lamps of devices of lighting and light alarm system
1.4.6. Care of a body and interior of the car
1.5. Tables
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 








1-4-4-13-zamena-shhetok-ochistitelya-vetrovogo-stekla.html

1.4.4.13. Replacement of brushes of screenwash

Pollution of a windshield and edges of brushes of a screen wiper various substances reduces quality of purification of glass. Treat similar pollution, for example insects, the juice emitted by leaves of trees and also polishes which apply in a hot state on a car body on some automobile sinks.
If brushes badly purify glasses, wash out glass and edges of brushes an effective cleaner or soft detergent, then carefully rinse them clear water. If necessary repeat processing of glass and brushes. Bad work of a screen wiper can be caused by wear or cracks of edges of brushes. Replace worn-out edges or brushes.
1. Lift the lever of a screen wiper and turn a brush concerning the hinge so that to open access to a plastic pad of a clamp.

Fig. 1.182. Scheme of replacement of brushes of screenwash


Shift a brush down (on an arrow, as shown in the figure 1.182). Then remove a brush from the screen wiper lever.
2. Unbend the end of a rubber edge down and extend it from the holder.
3. Take out spring edges from a rubber edge and implant them into a new edge of a brush.
4. Carefully insert a new rubber edge. Then install a brush assembled on the screen wiper lever, working in the return sequence.

ATTENTION
Do not bend and do not throw out spring edges. They are subject to reuse. If not to establish spring edges in an edge, quality of purification of glass will worsen.
It is forbidden to use the spring edges removed from the left brush of a screen wiper for installation in the right brush and vice versa. Be convinced of installation of spring edges in a new edge of a brush of a screen wiper that the bend of an edge remained the same.


"previous page
1.4.4.12. Replacement of the filtering air cleaner filter element
following page"
1.4.4.14. Service of the rechargeable battery